Anker’s Ultra Slim Extended Battery Case provides the best mix of good performance, price for that capacity, and physical size (the volume of bulk it boosts the phone). It offers the capability to supply 117 percent of any full charge to an iPhone 6 or 108 percent with an iPhone 6s. The price tag, $40 at the writing, is crazy low to get a battery case: In that rate, the Ultra Slim offers the best charge value (a 2.9 percent charge per dollar, or $34.34 for a full charge, for the iPhone 6) of any of the cases we tested, definitely.
The Ultra Slim doesn’t provide an especially premium feel. That’s not saying which it comes off as cheap, but nothing about its physical construction is particularly impressive next to other cases. Another minor strike against this Anker case is its insufficient button coverage; we typically prefer (well-designed) press-through button covers that protect the iPhone’s various buttons and reduce the amount of places where dust and dirt could get below the iphone6 case supplier.
For that iPhone 6 Plus and 6s Plus
Anker doesn’t make an Ultra Slim for the iPhone 6 Plus or 6s Plus, so for all those handsets, we like the Tylt Energi Sliding Power Case. Unlike most of the models we tested, this one carries a separate protective case that you could slide out of your battery sled whenever you don’t have to have the extra power, which makes it a far more-practical choice for the already huge Plus models. It’s yet another great power source, providing generally a 93 percent charge to the iPhone 6s Plus in our tests.
An important thing to remember together with the cases we dismiss below is because they are certainly not necessarily bad. Although we’re noting any issues we saw using these cases, a few of them are fine-they just can’t quite match up on the top quality of our own picks.
Our previous pick to get a more protective case was Speck’s CandyShell. A perennial favorite, it has two layers of material-plastic on the exterior, rubber on the inside-that provide more protection than case designs which can be just one or the other. The CandyShell is 10.9 mm thick, which puts it about the chunky side, however it doesn’t feel exceptionally bulky, and it’s one from the only cases we tested claiming in order to meet military drop-test standards. Speck gives the case in a wide range of colors, and variants add rubbery grips (CandyShell Grip), credit card holders (CandyShell Card), and graphic prints (CandyShell Inked).
The CandyShell includes a few problems that ensure that is stays from as a top pick, though. First of all, the CandyShell’s glossy back right away attracts small scratches that generally aren’t visible directly but jump out once you look at the iPhone in an angle. Granted, these scratches don’t modify the protection the situation offers-and we’re naturally happier to discover scratches around the case instead of around the phone itself-but it would be nice if Speck were to offer the case by using a matte finish.
The other concern is the case’s shape. A lot of our readers, in addition to a contingent of Amazon reviewers, take issue with the point that the CandyShell’s back is slightly convex. Specifically, if you set the way it is over a flat surface, this “hump” causes the way it is to rock whenever you press along any kind of its edges, or spin just like a top in the event you push it. (Should you bought a CandyShell and you mind this spinning and rocking, Speck says to contact its customer service department.)
OnePlus (the Android phone maker) surprisingly decided to go into on the iPhone-case game having its Sandstone Case. The major draw is OnePlus’s Sandstone texture; TIME says that it “feels like smooth sandpaper” and that “[i]t’s super grippy, rendering it very difficult to drop.” Unfortunately the case is a shell with open top and bottom edges, meaning it’s less protective when compared to a good case ought to be. For this reason design drawback, it fell out from competition.
SwitchEasy includes a mixed history, one that means it is tough to tell the entire story based upon its cases alone. Its Numbers case was our original pick to the iPhone 5 and 5s, before a wave of reader complaints about quality and customer satisfaction. The answers we got from SwitchEasy weren’t thorough; mostly, the business blamed the problems on third-parties selling knockoffs from the products. (At iLounge, I found the SwitchEasy protectors to become impressive generally-the Numbers earned a rare A rating from me-but readers there contacted me about similar issues.) Ultimately, we pulled our recommendation.
With all that under consideration, we checked out three SwitchEasy cases for your iPhone 6. The very first is the Odyssey. Like a few of the better cases we’ve evaluated, it’s a combination of plastic and rubber. Instead of being layered, the types of materials run side by side, together with the hardened rubber making up many of the case. It isn’t the prettiest case, within our opinion, yet it is protective. It covers the buttons without reducing a lot of their clickiness, and six holes along the important thing up precisely using the speaker vents. Our favorite area of the case is definitely the port protection: Rubber protectors squeeze into the headphone and Lightning ports, respectively, when they’re not being used, keeping dust and also other debris out.
SwitchEasy’s Tones includes the same port protection and uses the identical materials. Your body is mostly plastic, though, using the rubber walking around the sides as being a border in addition to across the back of the case, matching the iPhone’s antenna lines. We’d should you prefer a layer of rubber between your handset and also the plastic back of your TPU iphone6 case manufacturing , along with the Sleep/Wake button requires a bit an excessive amount of pressure about the few units we tested.
Our initial impressions of SwitchEasy’s Numbers were very positive-we were willing to name it as being our top pick-but there’s considerably more on the story than merely our review units, and we found a significant fault after a little extended use. This example is almost just like the Incipio NGP, however it provides more protection. Instead of leaving the phone’s ports totally exposed, the way it is provides protectors that fit in the headphone-jack and Lightning-port openings to maintain dust and debris out. It’s a great touch that’s executed well. Even phone’s speaker is way better protected, with six individual holes rather than one long opening. We actually like the tactility from the devqpky94 a bit more with SwitchEasy’s model than with Incipio’s case, too. An earlier yellow version of the case we tested accumulated permanent stains, but later iterations exhibited no such issue. However , the situation is a bit too loose, therefore the corners appear too easily. We experienced this issue time and again while removing the encased phone from your pockets. Because we’ve had other issues with SwitchEasy cases in the past, we’re still a bit wary. Should you do plan to invest in a SwitchEasy case, we recommend buying it directly through the company’s website. Doing so will eliminate any potential warranty difficulties with third-party sellers, should you have any troubles with the case.
A vital thing to remember together with the cases we dismiss below is that, unlike along with other categories of products we cover, they are not necessarily bad. Although we’re noting any issues we saw using these cases, a number of them are fine-they just can’t quite match up for the top quality of the picks.
Combining a rubber skin having a plastic frame, the Spigen Neo Hybrid is actually a slim, attractive case. Its fatal flaw lies in its button protection. The silver plastic pill within the Sleep/Wake button doesn’t depress properly, so it may possibly not hit the control underneath, so you likely won’t feel it if this does. Former Sweethome editor Joel Johnson confirmed this issue using the iPhone 6 Plus version. Because we received this situation for testing so early, we believe Spigen might revise later editions to handle this challenge.
Also from Spigen is definitely the Ultra Hybrid, a single-piece case that fuses a rubber frame using a clear plastic back. It’s a good-looking case, but when again, it provides issues with the buttons. As an alternative to putting raised material over them, they have left and right edges that are flat from top to bottom with small indentations. For that Sleep/Wake button, the indented label says “PWR,” and for volume, you will get plus and minus signs. Without having a more pronounced physical distinction, it is possible to quicker miss the buttons, and also the frame moves inward when you press.
Twelve South is in the beginning about exactly how protective the SurfacePad is. In the FAQ area of the case’s website, the corporation says, “SurfacePad for iPhone is not designed to protect iPhone from falls, drops, being run over by way of a car or dropped in the loo. SurfacePad is supposed to guard your iPhone from scratches and scrapes from things like car keys, nail files or concrete park benches.” It’s actually a lesser case plus more of any leather sticker by using a cover. The SurfacePad adheres to the rear of the iPhone, and you may eliminate it and reapply it as being necessary (though doing this is not as basic as the organization could have you feel). We love the materials, but the SurfacePad is difficult to recommend unless your main problem is fashion.
The Vault Slim Wallet from Silk can be a much-less-expensive alternative to sister company CM4’s Q Card Case. It’s basically the same design, except rather than a faux-leather back, everything is made from TPU. Such as the Q Card Case, the Slim Wallet can take three cards, but an elevated arch in its card slot causes the cards to curve to your noticeable degree, which could damage the cards after a while. The Q Card Case’s positive attributes otherwise carry over, but due to the card bending, I’m somewhat wary of the Slim Wallet.
Silk even offers the Armor Tough Case and PureView Clear Case. The Armor Tough Case is actually a rubber case with interchangeable, polycarbonate-plastic backplates. It’s an effective case at reasonable prices, but it’s thicker than than our top pick, the NGP. The PureView Clear Case, on the flip side, is really a nice pick inside the very full group of cases with rubber edges and clear backs, and Silk prices it aggressively. But we’re not terribly fond of this style because of dust’s propensity to have under the transparent back, and because of the convenience which the plastic can scratch. Still, beside others we’ve tested, the PureView Clear Case has pleasant-feeling buttons and well-sized port openings.
With Incipio’s Rival, unlike using the NGP, only the border is TPU; the rest of the Rival is difficult plastic, about .3 mm thicker compared to NGP. Everything in regards to the case is basically just like in the NGP, including the cutouts for that ports and the grade of the button protection. Even though the Rival is very smooth, similar to the NGP, horizontal lines over the lower two-thirds of its back give a distinct texture. It isn’t as neutral because the NGP, but if you appreciate the style, it is actually a great option.
Tech21’s Evo Mesh, which features the second generation in the company’s shock-absorbing lining, is an Apple Store exclusive. Much like Tech21’s Classic Shell (more on this design below), it’s a rubber case by using a colored band running around the perimeter. The dimensions are virtually identical between the two. There’s something about this one which we like greater than the Classic Shell, but it’s challenging to put a finger of what that is. Perhaps it’s that this somewhat-obnoxious orange band has become replaced by colors matching the different body shades of the case itself. Overall, though, this situation is too pricey for what it gives you.
Plastic and rubber by using a clear back, the ITSKINS Venum Reloaded drops the ball with regards to within the iPhone’s buttons. Similar to the setup of Spigen’s Ultra Hybrid, the design of your Venum Reloaded makes hardly any physical distinction between the button coverage and all of those other case. This example had also been relatively expensive when last we checked, along with the plastic border frame feels fragile.
Really a greater portion of a fashion case, the Nitro Forged from ITSKINS currently costs quite a penny at nearly $70. It includes a rubber skin with machined aluminum caps that attach on the top and bottom. Thankfully, this design is definitely an improvement over previous versions, which required one to use an included screwdriver to set up and take away the caps; instead, it uses small plastic clips that you can devote and take away manually.
Also from ITSKINS may be the Evolution. A rubber core by using a plastic frame, the Evolution has some curves that assist allow it to be feel a little more organic. The big problem is the fact that screen rises on top of the side of the situation instead of the other way around. This means that if you drop your handset, there’s far more likelihood of damage to the display when compared with other cases.
Incipio makes countless cases which we can’t expect great things away from every one. The Advantage is a plastic slider, a style that’s relatively rare these days. The smooth, matte-finish plastic splits into two pieces for installation and docking purposes. While it offers proper button coverage and a nice protective lip, we found the way it is to be too tight; pulling it away, specially the bottom cap, is a struggle.
Weighing a couple of grams a lot more than the standard of all of the cases we tested, the DualPro SHINE is a solid contender from Incipio. It incorporates both plastic and rubber layers, although as an alternative to being molded together, they’re two distinct pieces. The rubber is reasonably thick but doesn’t dampen the tactility in the buttons by any means, plus it still provides acceptable accessibility ports. The port openings are identical to the NGP’s. We also looked at the standard DualPro, that features a matte finish. It’s quite nice, but it’s thicker compared to the NGP and lacking the mil-spec rating of your CandyShell.
The plastic layer of your DualPro SHINE fits into grooves in the rubber, helping the case feel like a cohesive unit. We believe the most polarizing thing about this case is its texture: Created to seem like brushed aluminum, it certainly doesn’t seem like that, as well as at least within our tests, the result is a certain degree of cognitive dissonance. It’s not a bad thing by any means, but overall it just doesn’t feel quite as nice mainly because it looks.
If card storage is vital to you personally, Verus’s Damda is really a fine case. The entire body is made of black rubber, with nice button protection and effectively centered openings to the headphone port and microphone, the Lightning port, as well as the speaker. Attached to the back is actually a plastic compartment that adds both mass and depth. A plastic door slides available to reveal space for two, maybe three, a credit card. We initially thought it was a bit tough to open, although with some cards inside it’s easier to work with yet still secure. This is a greater portion of a distinct segment case than our pick.
Verus’s Crystal Mixx provides a transparent window including a rubber frame. Your back for this one is plastic, which is one of these two drawbacks. In our exposure to iPhone cases, clear plastic scuffs easily and may show those scratches within an issue of days. This case is probably not so bad in case the frame provided a greater lip. Unfortunately, at .3 mm, it’s one from the shortest lips we saw, and it could lead to problems if you drop your iPhone.
The Protector Case and Voyager Case from Pelican look a whole lot alike, and each model is difficult to find-Pelican doesn’t sell them online, as well as in our experience they’ve been reliably available only at AT&T retailers. The Protector is a bulkier, more-angular carry out the CandyShell design without having additional benefits, so we’d pass onto it. The Voyager adds port protection and funnels the sound from the speakers forward. In addition, it has a belt clip and screen film. We have seen this model instead of an OtterBox case, as it’s basically overkill. A lot of people simply don’t need this degree of protection, especially not when they have to fall out of their strategy for finding it.
PureGear’s Slim Shell Case is available in seven color combinations, including clear-on-clear. This model is hard plastic having a rubberized but nonetheless rigid frame. The metal button covers can be a really nice addition, helping the case feel more premium. It won’t offer just as much protection being a CandyShell, therefore it isn’t a top-notch pick, but this one isn’t a bad option whatsoever.
One of the first iPhone 6 cases to become publicly sold-we saw it since May 2014-Minisuit’s Frost is an inexpensive TPU skin. Although it does fit, they have virtually no lip, and also the holes along the bottom are uneven to the point of looking warped.
Monoprice is recognized for inexpensive products of all types. We love to some of the company’s accessories-it makes great cables, for example-but Monoprice cases generally don’t impress. Materials often feel cheap, along with other companies offer higher-quality products at similarly discount prices. By way of example, the Metal Alloy Protective Case (for sale in gold, silver, and cosmic blue) includes a thin, aluminum shell that snaps more than a thin TPU skin, with lines matching the iPhone’s antenna breaks. The TPU doesn’t feel as nice as the material that Incipio and also other companies use, along with the case exposes the Apple logo on the rear of the phone.
Monoprice’s Industrial Metal Mesh Guard Case (in black or white) feels a bit nicer but is even less protective. The plastic shell has includes a cool-looking steel grille over it, nevertheless it leaves the most notable and bottom edges unprotected, and yes it features the greatest Apple-logo opening we’ve seen on any case.
We examined the TPU case from Insignia, a Best Buy brand, plus it is apparently through the same OEM as Monoprice’s TPU case, but at a higher price.
We don’t just like the Monoprice PC TPU Protector Case quite as much, although it does offer arguably more protection. This model splits into two pieces, having an inner skin of TPU plus a polycarbonate shell that snaps in place over it. The situation is fairly simple to assemble, but when it’s together, it merely feels big. It’s both wider and thicker than the NGP, without having obvious advantage apart from price.
Rokform has long focused entirely on ruggedized cases that can connect to an ecosystem of mounting accessories. Its Sport v3 is not any exception. This plastic and rubber case comes along with swappable magnetic backplates that allow it to connect with various mounting brackets the company sells. Unfortunately, the instruction insert lists a dealbreaker: “Magnet will disable NFC on phone.” These days the company claims how the magnet won’t obstruct Apple Pay or any antennas, but we haven’t tested this.
OtterBox’s Defender Series is the bulkiest from the cases we’ve tested up to now. This is basically the company’s flagship case, the one many people associate with the brand. It’s consisting of a plastic frame that snaps throughout the handset along with a thick rubber skin that covers everything. Unlike many other cases, this model includes flaps across the vibration control switch, headphone port, and Lightning port-all good things on an extra measure of protection. In addition, it includes button coverage, but we found that it needs more force to depress the quantity and power controls than other cases do.
The Defender Series is also really the only case we’ve tested with built-in screen protection such as a specific film incorporated into the frame. Because you end up with a little space involving the protector as well as the screen, very light presses and swipes may not register, which is actually a drawback. Atop the Touch ID/Home button is actually a thin sheet of plastic that didn’t hinder the ability in our testing. Even though the Defender Series does expose the Apple logo, the way it is at least covers it with clear film that prevents it from getting scratched. And also as an added bonus, the Defender Series comes with a belt holster.
Within the OtterBox family, the Commuter Series represents the next step down in overall protection. Instead of plastic internally and rubber on the outside, the layers are reversed. The way it is still offers port coverage, nevertheless the switch about the iPhone’s left side remains exposed. Thankfully, the buttons depress far more easily. As opposed to a permanent screen protector, OtterBox includes an optional film with this particular case. The Apple logo is again exposed, now with no plastic covering it. Apart from the port protection, this example offers no obvious benefits spanning a CandyShell, and the size is a drawback that keeps this model from earning a high spot.
The Symmetry Series is really a relatively recent accessory for the OtterBox lineup as well as the slimmest of them all. It feels as though a direct answer to the CandyShell, with its dual-layer design. This case gives the same amount of protection as our top choice and a substantial lip. It’s taller and wider, though, in a higher price. The most significant benefit is the fact that by using a matte-plastic back, it won’t show the scratches a CandyShell does.
OtterBox’s newest case, the Statement Series, is an iPhone 6/6s-specific case. An iPhone 6/6s Plus version exists, but unlike OtterBox’s other lines, this series offers no version for older iPhones or any other flagship smartphones. It’s also one of your few OtterBox cases that put aesthetics first, having its large back-panel window and leather-covered lower quarter being its key distinguishing features. We’re testing the Statement right now, and we’ll decide whether or not this should join our picks soon.
Hard Candy Cases Candy Clip Series is a fairly crazy proposition: For $30, you have a hard-plastic X-shaped piece that snaps onto the back of the iPhone, covering its corners and a few of the edges but leaving the buttons and most of the sides exposed. No thanks.
Urban Armor Gear’s Case is one of the only cases we’ve tested to fulfill military drop-test standards. It’s excellent like a protective case, however its industrial aesthetic lacks the broad appeal of simpler designs like those from Incipio and Speck. UAG also combines plastic and rubber in this case, but instead of a glossy finish, it relies on a matte one, with an industrial appearance that appropriately matches the brand’s name. With ridges and fake screws, it looks like an issue that would not be out of place over a construction site. We all do take problem with the 2 small, rectangular holes on the rear of the situation-in regards to a quarter of how in the top or bottom, respectively, they expose part of the logo along with the top 1 / 2 of “Phone” from the iPhone label. It’s an unusual design decision with an otherwise impressive case. However, this model does have a screen film, whereas most iPhone cases don’t today.
Tech21’s entire product lineup is dependant on D3O, a qualified material the business uses in each and every one of their cases. Mostly contained in the borders of Tech21 cases, the bright-orange material is supposed to remain soft when at rest but automatically harden upon impact, dissipating the force and ultimately preventing injury to your phone. The organization really likes to show off the stuff; all of its cases are at least translucent, or even transparent, around the edges.
From Tech21, we tested the Classic Shell, Classic Shell Cover, and Classic Shell Flip. The first is the most basic, a glossy TPU skin that’s wider in comparison to the NGP, due to the layer of D3O. We’d want to notice a bigger lip than this situation offers, and also the buttons certainly are a bit squishier than we generally prefer. The Classic Shell Cover keeps the same frame but replaces the TPU around the back having a hard-plastic plate, and it has an attached cover to shield the iPhone’s display. Everything else works the same as using the standard model, along with the lid includes a cutout across the earpiece so that you can speak on the phone with it closed. The Classic Shell Flip is actually the identical, only as opposed to plastic this example includes a leather feel (it seems to be the fake stuff), as well as the lid comes around through the bottom as opposed to the side. We find that lids get in how more than they guide, so neither of those covered models excites us, as well as the soft buttons and wider body from the Classic Shell prevent it from getting a recommendation.
From iLuv, we received two cases for evaluation: the Aurora Wave and Gelato. First is a straightforward silicone skin having a grid about the back that glows at nighttime. When it comes to body coverage, the case lives as much as what we’re looking for, but making this sort of design involves a low level of difficulty. As we’ve often found with cases on this style in the past, the vertical edges can pull outside the body in the phone more readily as compared to other cases, allowing dust along with other particulates to get underneath. The Gelato, on the flip side, is TPU iphone7 case with an attractive checkerboard pattern about the back. It appears and feels very good, however the .33-millimeter lip is simply too short.
Poetic’s Atmosphere is a thin case created from dual-molded polycarbonate plastic and TPU. The softer material rings the leading edge to make a small lip, and it likewise runs on the antenna breaks on the back of the phone. While this transparent case initially appears like a nice option for individuals that desire a slim protector yet still want to demonstrate their iPhone, it falls short because of button protectors which require too much force to press.
Macally shipped us a few different cases, but two turn out to be styles we simply can’t recommend. Both the Metallic Snap-On Case along with the Flexible Protective Frame come in a number of colors, although the former is a shell, as well as the latter can be a bumper that protects the sides but leaves the scratchable back exposed. The Durable Protective Case, as opposed, does offer more thorough protection, however it isn’t a genuine design. A combination TPU skin and hard-plastic frame, this situation kind of seems like an armadillo from the back. We’ve already seen at least one other company supplying the same case, and that we weren’t impressed with that case’s aggressive looks either.
New Trent’s Alixo 6S isn’t necessarily the prettiest case around, but it is one of your more original designs we’ve noticed in the pile. This two-piece case includes front frame (black- and white-rimmed versions are contained in the package) along with a silicone rubber and plastic back. You simply snap the phone into the selection of frame then insert it to the back piece, which include flip-open port protectors. The volume of protection this model offers for that price is impressive, since it incorporates a built-in screen film and Touch ID coverage. However the latter happens to be the Alixo 6S’s downside: Even though the fingerprint sensor does deal with the thin material over it, we found so that it is less reliable, requiring more tries to unlock the product.
Marblue’s ToughTek can be a thick silicone rubber case that accompanies a screen protector. Basically we don’t doubt it can tolerate some significant drops, the ToughTek is big-3 inches wide, 5.8 inches tall, and .6 inch deep-and particularly difficult to get in and out from tight pockets because of the grippy material. It may possibly not be considered a bad option if you’re handing your iPhone 6 to kids.
The Elite, also from Marblue, takes its inspiration in the CandyShell, while incorporating an Aztec-like pattern. The plastic and rubber layers intersect in horizontal and vertical lines, with the latter material sticking up above the hard plastic. One of the most intriguing point about this case will be the set of inch-long ridges, one on each side. They’re made to work with a multitude of accessories, including a belt clip. We’ll be keeping an eye out of these accessories, and we’ll decide if they boost the price of the situation.
We had high hopes for the Spigen Capella, which comes in multiple colors. Its setup is very similar to the CandyShell’s, with rubber inside and plastic outside. The important difference, along with the reason we were pumped up about it, is it’s much slimmer, measuring about 2 mm thinner from front to back. This can be partly due to the smaller, half-millimeter lip round the screen. One of our editors loves the way the case’s slight curve feels, comparing it to the iPhone 3G. Judging from the feedback we’ve seen from readers and Amazon reviewers, many people don’t such as that shape just as much as we do.
While the Capella isn’t as deep as the CandyShell, it is a bit taller, and approximately 3 mm wider. This width winds up being problematic for just two reasons, one on either edge. In the iPhone’s left side, the switch is much harder to toggle, as it’s deeply recessed in the rubber border; should you don’t have nails to communicate of, moving it back and forth will probably be tough. On the other side, the Sleep/Wake button needs a surprising amount of pressure to activate. If you’re willing to manage those drawbacks, the Capella is otherwise worth taking into consideration as a CandyShell alternative.
Featuring its Revolution case, Poetic looks to contend with companies such as OtterBox at a far lower price. The case starts off with a plastic frame that snaps on the front of the iPhone; a definite sheet of plastic protects the screen while leaving the sensors on the top along with the Touch ID button at the end exposed. A rubber and plastic body fits around the back, snapping into position using the front piece. Everything feels quite sturdy, the buttons click well, and the flap on the Lightning port is a nice little extra protection.
Supcase’s Unicorn Beetle Pro Holster provides a similar proposition. The biggest distinction between this model as well as the Revolution is it features a plastic belt holster. Having roughly exactly the same dimensions as being the Poetic case, this model requires an installation that’s just about the same. This example adds a few flaps for coverage, namely over the side switch and the headphone port besides the Lightning port. While it’s a very solid-feeling case, we immediately referred to as company’s claim of dust-proof construction into question, because it leaves openings for dust to get in, such as the fully exposed speaker. Right now, Amazon users are usually fond of it, with 127 reviews along with a 4.1-star (away from five) rating, but we’ve seen a number of three- and four-star reviews.
Relative newcomer Supcase has a number of iPhone 6 cases, the truth is, nearly all of which are portion of the “Unicorn Beetle” family. The Slim Armored Protective Case is a lot like Urban Armor Gear’s case in this it’s protective, but the design is quite specific, meaning it likely won’t entice a similar wide swath of folks as something much more generic. The plastic and rubber case feels sturdy and contains some of the clickiest buttons associated with a we tested. With regards to lip, it’s only about .5 mm, so it’s smaller compared to we’d like, and also the case makes no mil-spec claims. If you appreciate the appearance, it’s not a bad choice otherwise.
Supcase also sells the Hybrid Clear Bumper Case, which combines a definite-plastic backplate using a TPU bumper. That polycarbonate back won’t absorb the maximum amount of shock as the thick rubber border, but it’s the best way to show off Apple’s design.
In the previous version of the guide, we named Logitech’s Protection [ ] as a more-protective pick. It comes with a very similar design, with the benefits of a matte finish and embedded magnets that allow it to connect with mounting accessories. Unfortunately Logitech has confirmed that it’s no longer selling the truth, that is currently on clearance at Best Buy.
Not one other case we tested is to establish exactly the same way as Maxboost’s DuraShield Series (now named DuraSLIM). Like a number of other models, it uses both rubber and plastic components, but here the rubber is actually a bumper that wraps around the iPhone’s border, and also the plastic snaps in position over it while covering the rear of the handset. Inspite of the unusual design-or perhaps for doing it-the case offers superior protection in contrast to lots of others we’ve seen. It includes a 1-mm lip, plus speaker and Lightning-port protection. Additionally, it redirects the audio ports forward, meaning the sound comes to you, rather than down; the design has no effect on audio quality, thankfully. When it comes to Lightning port, it stays protected underneath a rubber tab that you could flip out when you want access.
Few case manufacturers actively warn that the product doesn’t offer drop protection, but just this kind of message appears on the Amazon listing for Maxboost’s Liquid Skin. Extremely thin, this transparent-TPU case adds very little bulk on the handset, not a protective lip. It’s superior to a shell since it offers button protection and cutouts for your ports, even if they are quite tight. Although with this sort of warning from the case maker itself, we can’t recommend the Liquid Skin for many people. If you’re going to use a case, you should use something that’ll stand up to a drop.
Maxboost’s Crystal Cushion and i also-Blason’s Halo Series are almost identical to one another and also may be small tweaks about the same reference design. Have rubber frames-the Halo Series offers six colors, plus clear-with transparent plastic backplates. The Maxboost case’s edges are definitely more squared-off, as the i-Blason’s are rounder. Both offer good body coverage and responsive buttons, although the lip throughout the screen is virtually nonexistent, especially on the Halo Series. Combine by using the tendency for clear plastic cases to scratch as well as expose trapped dust underneath, which cases aren’t top picks.
The Maxboost HyperPro Series is for all intents and purposes a thicker version in the Incipio NGP. Available only in black, it uses two layers of TPU to guard the iPhone, and it measures 10.2 mm thick; it’s also wider and taller than our pick. The buttons press well plus it incorporates a protective lip, but we could find no real advantage of this example on the NGP, besides savings of just a couple of dollars.
One of just a couple of slider-style cases around, Maxboost’s Vibrance Series supplies a different build than most of the cases we tested. A tough-plastic case, it splits into two pieces, both lined by using a soft fabric across the back that’s meant to prevent damage during installation and removal. As opposed to pushing the phone in the case, you accomplish the base cap, slide the phone in the top, after which push the pieces back together again. Much as with the STM Harbour, this kind of design enables you to keep your iPhone thoroughly protected more often than not, and to plug it into docks when necessary. The lip is sort of short, though, and pulling from the Vibrance’s bottom cap is harder than flipping the Harbour’s bottom. Maxboost now offers only one color choice, salmon having a gold cap, which might not attract as many people as more basic colors would.
If you discover the CandyShell to be too large, you won’t be impressed with Speck’s MightyShell, which comes in black, orange, purple, pink, and clear variants. This model comes with a few key differences. First may be the extra layer of TPU material which helps absorb shocks to your greater degree; it adds 2 mm in width and height, and also .5 mm for the thickness in the case. Speck claims that the new design will “double MIL-STD-810G drop test standards,” but we can’t tell whether this means the way it is is tested to outlive drops from two times as high or this means the situation can tolerate the regular 4-foot drops twice as many times. One part of the case we actually appreciate is the hard-plastic exterior, which can be matte as an alternative to glossy, so that it won’t show scratches nearly as readily as being the standard CandyShell. To the price, we expect more than simply claims of better drop protection; conditions in which this example would survive but a CandyShell wouldn’t are far too ambiguous to justify the fee.
Among ultrathin cases, Shumuri’s SLIM looks and feels very similar to Caudabe’s The Veil XT, to the absence of the standard Veil’s screen-protection lip. But it’s also missing both Veil models’ camera-lens protector. The same goes for Monoprice’s Ultra-thin Shatter-proof Case (in clear frost, ice blue, and smoke) and Totallee’s The Scarf (for iPhone 6 and iPhone 6 Plus).
Rearth USA’s Ringke Slim (for iPhone 6 and iPhone 6 Plus) offers both a screen-protecting lip and bottom-edge coverage, as well as thicker plastic for further protection. However, we’re not fans of the aesthetics-for the reason that case’s rigid plastic is thicker, the organization has added a little slit to every corner to produce putting the case on the phone easier. The design is useful enough; we simply don’t like the actual way it looks.
Power Support’s Air Jacket and SwitchEasy’s Nude (for iPhone 6 and iPhone 6 Plus) are glossy-plastic cases which are slightly thicker than Caudabe’s The Veil. The former provides good coverage across the phone’s bottom edge but only has the very faintest of the screen-protection lip. The second has neither.
Amzer’s Crusta may not appear to be an excellent value at $35 (iPhone 6) or $45 (iPhone 6 Plus) since this writing, nevertheless the package includes not only a simple case. The situation itself works with a two-piece snap-together design using a rubber bumper as well as a glass back that lets the iPhone’s rear show through. The glass likely won’t show scratches as easily as similar cases we’ve seen having a plastic back, however, you will still see any dust, hair, or some other particulates which get beneath the glass. Amzer contains a second component of glass to guard the phone’s screen. The truth winds up being bulkier than we prefer-the iPhone 6 version is 14.4 mm thick, including the phone-but it’s one from the better cases we’ve seen from Amzer, an organization otherwise recognized for inexpensive, nondescript accessories.
NewerTech is recognized more for computer accessories than smartphone accessories, nevertheless the company does offer a collection of cases called NuGuard KX (for iPhone 6 and iPhone 6 Plus). Made more for drop protection than sleekness, the NuGuard KX boasts a thick layer of gel material that absorbs and evenly distributes shocks. The truth is quite bulky, yet an opening on the back of the case for the phone’s Apple logo actually subtracts from the overall amount of protection. We choose the NGP.
We certainly have varying degrees of praise for three cases from Griffin Technology. The Survivor Slim (for iPhone 6 and iPhone 6 Plus) is our least favorite of these. This bulky rubber case feels similar to an accessory for the kid’s toy than a smartphone. It could be an excellent case if children frequently use your phone, but we suspect that a majority of adults will prefer something slimmer.
We like the Survivor Core (for iPhone 6 and iPhone 6 Plus) and all of Clear Identity (for iPhone 6 and iPhone 6 Plus) better. Both allow the handset’s to show through a clear back panel. The previous has rubber edges, as well as its rubber corners protrude a bit, helping to cushion the iPhone against drops-although the end result is that it’s a little bigger than a normal case. The All Clear Identity, however, includes a transparent back with translucent-rubber edges. The problem, as with most cases sporting a clear back, is both cases show any gunk that gets under the plastic. For many people, that could be a sufficient compromise in a case designed to let you watch your phone’s own surfaces, but we generally prefer something translucent or opaque. Neither the Survivor Core nor the All Clear identity is really a bad option, but neither particularly excites us.
Belkin’s Grip Case for iPhone 6 is a superb replacement for our top pick, but it doesn’t quite make the top tier. The design is much like those of the Incipio NGP, as it’s a one-piece polyurethane case. The most significant difference is over the phone’s bottom edge: As opposed to having separate openings for your headphone jack, microphone, Lightning-connector port, and speaker, the truth exposes the past two through one long opening. A slight indentation within the plastic covering the foot of the phone provides for use with accessories like Apple’s Lightning-connector adapters. This can be a nice feature that we haven’t seen on other cases, although we worry that this thinness of your material here, as well as nearby the Ring/Silent switch, may make it more vunerable to ripping. Wirecutter editor Michael Zhao also finds the case’s button coverage being somewhat problematic, since he doesn’t that way they’re nearly flush together with the case.
On the list of cases shipped to us for consideration, we dismissed a variety of models right off the bat. We cut Spigen’s Slim Armor, Slim Armor S, Tough Armor, and Tough Armor S, along with Verus’s Thor, Iron Shield, and Dandy Diary, plus PureGear’s DualTek, due to their Apple-logo-exposing holes around the back. They generally do a significant job of protecting your phone otherwise, but we can think about no reason at all to recommend them for many individuals when existing hole-free options are nearly as good or better.
We also dismissed a variety of shell cases because, as we mention above, they offer a minimal quantity of coverage for the device’s body. Among these were the Aluminum Fit, Thin Fit, and Thin Fit A from Spigen. The same goes for your Neo Hybrid EX, Spigen’s bumper case, that offers much less protection.